Armorseal Crack Filler

THE Heavy 8.22SHERWIN-WILLIAMS ARMORSEAL® 1000HS DutyCOMPANY PART A B67-2000 SERIES PART B B67V2002 HARDENER Floor CoatingsINDUSTRIAL PRODUCT INFORMATION Revised 1/02 & MARINE COATINGS PRODUCT DESCRIPTION RECOMMENDED USESARMORSEAL 1000HS is a high solids, heavy duty, two-com- • For industrial, commercial, or marine applications where aponent, catalyzed, polyamide epoxy coating formulated for de- heavy duty epoxy coating is required.manding marine and industrial requirements. This dries rap-idly to a tough, high gloss finish with excellent resistance to • Superior resistance to chemicals, moisture, abrasion, andalkalies, abrasion, corrosion, and chemical attack. impact• Suitable for use in USDA inspected facilities • Meets ADA requirements for slip resistance for floors• Chemical Resistant • Excellent resistance to alkalies, dilute acids, spillage of• Impact Resistant• Abrasion Resistant solvents, chemicals, jet fuel, grease, etc. • Clear finish for interior use only PRODUCT CHARACTERISTICS PERFORMANCE CHARACTERISTICSFinish: Gloss System Tested: (unless otherwise indicated)Color: Clear, Haze Gray, Deck Gray, White, Substrate: ConcreteVolume Solids, mixed: Sandstone, Tile Red, Safety Yellow, may vary by color and a wide range of tinted colors Surface Preparation: Clean, dry, soundWeight Solids, mixed: colors—65% ± 2%, White 1 ct. ArmorSeal 1000 HS (reduced) clear—61% ± 2% 1 ct. ArmorSeal 1000 HS @ 3.0 - 5.0 mils dft 74% ± 2%, may vary by color Abrasion Resistance: Method: ASTM D4060, CS17 wheel, 1000 cycles, 1 kg load Result: 64.8 mg lossVOC (EPA Method 24), mixed, may vary by color: Adhesion, over concrete: Method: ASTM D4541colors Unreduced: 330 g/L; 2.75 lb/gal Result: 865 psicolors Reduced 10%: 365 g/L; 3.05 lb/galclear 392 g/L; 3.27 lb/galMix Ratio: 1:1 by volume Direct Impact Resistance (steel): Method: ASTM D2794Recommended Spreading Rate per coat: Result: 58 in. lbsWet mils: 5.0 - 8.0 Dry Heat Resistance: Method: ASTM D2485Dry mils: 3.0 - 5.0 Result: 180°FCoverage: 206 - 350 sq ft/gal approximateNOTE: Brush or roll application may require multiple coats to achievemaximum film thickness and uniformity of appearance.Drying Schedule @ 6.0 mils wet @ 50% RH: Flexibility (steel): Method: ASTM D522, 180° bend, 1/8' mandrel @ 50°F @ 77°F @ 120°F Result: PassesTo touch: 4 hours 2 hours 30 minutes Pencil Hardness: Method: ASTM D3363To recoat: Result: HBminimum: 24 hours 8 hours 4 hours Slip Resistance, Floors: Method: ASTM C1028-96, .60 minimum Static Coefficientmaximum: 7 days 7 days 7 days of FrictionFoot traffic: 48 hours 24 hours 12 hours Result: Passes wet and dry, with and without SharkGripHeavy Traffic 4-5 days 48-72 hrs 24-36 hrs AdditiveTo cure: 10 days 7 days 4 days Epoxy coatings may darken or yellow following application and curing.Pot Life: 6 hours 4 hours 2 hoursSweat-in-Time: 2 hours 30 minutes 10 minutesIf maximum recoat time is exceeded, abrade surface before recoating.Drying time is temperature, humidity, and film thickness dependent.Shelf Life: 36 months, unopened, at 77°FFlash Point: 105°F, Seta, mixedReducer/Clean Up: Reducer #54, R7K54ArmorSeal 8.22 continued on back

ArmorSeal ® Floor Coatings. Our full line of ArmorSeal ® Heavy Duty Floor Coatings will stand up to anything from light foot traffic in retail stores to facilities with heavy vehicular traffic. Fillers & Putty Spackling & Patching Compounds Glazing Compound Patching Tape. Product Details. Preferred Customer PaintPerks from Sherwin-Williams.

THE Heavy 8.22SHERWIN-WILLIAMS ARMORSEAL® 1000HS DutyCOMPANY PART A B67-2000 SERIES PART B B67V2002 HARDENER Floor CoatingsINDUSTRIAL PRODUCT INFORMATION & MARINE COATINGS RECOMMENDED SYSTEMS SURFACE PREPARATIONConcrete/Wood: Surface must be clean, dry, and in sound condition. Remove1 ct. ArmorSeal 1000HS (reduced 1 pt/gal with R7K54) all oil, dust, grease, dirt, loose rust, and other foreign material1-2 cts. ArmorSeal 1000HS @ 3.0 - 5.0 mils dft/ct (with anti- to ensure adequate adhesion. slip aggregate if required) Refer to product Application Bulletin for detailed surface prepa- ration information.Concrete:1 ct. ArmorSeal 33 Epoxy Primer/Sealer @ 8.0 mils dft Minimum recommended surface preparation:1-2 cts. ArmorSeal 1000HS @ 3.0 - 5.0 mils dft/ct (with anti- * Iron & Steel: SSPC-SP6 slip aggregate if required) Concrete & Masonry: SSPC-SP13/NACE 6Steel:1 ct. Recoatable Epoxy Primer @ 4.0 - 5.0 mils dft Wood, interior: Clean, smooth, dust free1-2 cts. ArmorSeal 1000HS @ 3.0 - 5.0 mils dft/ct * Primer RequiredPainted Surfaces in Sound Condition:1-2 cts. ArmorSeal 1000HS @ 3.0 - 5.0 mils dft/ct TINTING White may be tinted using 844 Colorants at 200% tinting strength, 8 oz per gallon maximum, into Part A. Five minutes minimum mixing on a mechanical shaker is required for com- plete mixing of color. APPLICATION CONDITIONS Temperature: 50°F minimum, 120°F maximum Relative humidity: (air, surface, and material) At least 5°F above dew point 85% maximum Refer to product Application Bulletin for detailed application information. Packaging: ORDERING INFORMATION Part A: Part B: 1 gallon containers 1 gallon containers (clear available in 5 gallon containers) Weight per gallon: 12.51 ± 0.2 lb mixed, may vary by color SAFETY PRECAUTIONS Refer to the MSDS sheet before use.The systems listed above are representative of the products Published technical data and instructions are subject to changeuse, other systems may be appropriate. without notice. Contact your Sherwin-Williams representative for additional technical data and instructions.

THE Heavy 8.22ASHERWIN-WILLIAMS ARMORSEAL® 1000HS DutyCOMPANY PART A B67-2000 SERIES PART B B67V2002 HARDENER Floor CoatingsINDUSTRIAL APPLICATION BULLETIN Revised 1/02 & MARINE COATINGS SURFACE PREPARATION APPLICATION CONDITIONSSurface must be clean, dry, and in sound condition. Remove Temperature: 50°F minimum, 120°F maximumall oil, dust, grease, dirt, loose rust, and other foreign material Relative humidity: (air, surface, and material)to ensure adequate adhesion. At least 5°F above dew pointIron & Steel (atmospheric service)Remove all oil and grease from surface by Solvent Cleaning 85% maximumper SSPC-SP1. Minimum surface preparation is CommercialBlast Cleaning per SSPC-SP6. For better performance, use APPLICATION EQUIPMENTNear White Metal Blast Cleaning per SSPC-SP10. Blast cleanall surfaces using a sharp, angular abrasive for optimum sur- The following is a guide. Changes in pressures and tip sizesface profile (2 mils). Prime any bare steel the same day as it is may be needed for proper spray characteristics. Always purgecleaned or before flash rusting occurs. spray equipment before use with listed reducer. Any reductionPoured Concrete must be compatible with the existing environmental and appli-New cation conditions.For surface preparation, refer to SSPC-SP13/NACE 6. Surfacesmust be clean, dry, sound and offer sufficient profile to achieve Reducer/Clean Up ..... Reducer #54, R7K54adequate adhesion. Minimum substrate cure is 28 days at 75°F.Remove all form release agents, curing compounds, salts, ef- Airless Sprayflorescence, laitance, and other foreign matter by sandblast- Pressure ............ 2500 psiing, shotblasting, mechanical scarification, or suitable chemi- Hose ............... 3/8' IDcal means. Refer to ASTM D4260. Rinse thoroughly to achieve Tip ................. .015' - .021'a final pH between 6.0 and 10.0. Allow to dry thoroughly prior Filter ............... 60 meshto coating. Reduction ........... As needed up to 10% by volumeOldSurface preparation is done in much the same manner as new Brushconcrete, however, if the concrete is contaminated with oils, Nylon/Polyester or Natural Bristlegrease, chemicals, etc., they must be removed by cleaning with Reduction ........... As needed up to 10% by volumea strong detergent. Refer to ASTM D4258. Form releaseagents, hardeners, etc. must be removed by sandblasting, Rollershotblasting, mechanical scarification, or suitable chemical Cover .............. 3/8' woven with phenolic coremeans. If surface deterioration presents an unacceptably rough Reduction ........... As needed up to 10% by volumesurface, ArmorSeal 5020 Floor Resurfacer is recommended topatch and resurface damaged concrete. If specific application equipment is listed above, equivalentFill all cracks, voids and bugholes with ArmorSeal Crack Filler. equipment may be substituted.Always follow the ASTM methods listed below:ASTM D4258 Standard Practice for Cleaning Concrete.ASTM D4259 Standard Practice for Abrading Concrete.ASTM D4260 Standard Practice for Etching Concrete.ASTM D4263 Plastic Sheet Method for Checking Moisture inConcrete.SSPC-SP 13/Nace 6 Surface Preparation of ConcretePreviously Painted SurfacesIf in sound condition, clean the surface of all foreign material.Smooth, hard or glossy coatings and surfaces should be dulledby abrading the surface. Apply a test area, allowing paint to dryone week before testing adhesion. If adhesion is poor, or if thisproduct attacks the previous finish, removal of the previouscoating may be necessary. If paint is peeling or badly weath-ered, clean surface to sound substrate and treat as a new sur-face as above.ArmorSeal 8.22A continued on back

THE Heavy 8.22ASHERWIN-WILLIAMS ARMORSEAL® 1000HS DutyCOMPANY PART A B67-2000 SERIES PART B B67V2002 HARDENER Floor CoatingsINDUSTRIAL APPLICATION BULLETIN & MARINE COATINGS APPLICATION PROCEDURES PERFORMANCE TIPSSurface preparation must be completed as indicated. Stripe coat all crevices, welds, and sharp angles to prevent early failure in these areas.Mix contents of each component thoroughly with power agita-tion. Make certain no pigment remains on the bottom of the When using spray application, use a 50% overlap with eachcan. Then combine one part by volume of Part A with one part pass of the gun to avoid holidays, bare areas, and pinholes. Ifby volume of Part B. Thoroughly agitate the mixture with power necessary, cross spray at a right angle.agitation. Allow the material to sweat-in as indicated. Re-stirbefore using. Spreading rates are calculated on volume solids and do not include an application loss factor due to surface profile, rough-Apply paint at the recommended film thickness and spreading ness or porosity of the surface, skill and technique of the appli-rate as indicated below: cator, method of application, various surface irregularities, material lost during mixing, spillage, overthinning, climatic con-Recommended Spreading Rate per coat: ditions, and excessive film build.Wet mils: 5.0 - 8.0 No reduction of material is recommended as it can affect film build, appearance, and adhesion.Dry mils: 3.0 - 5.0 Do not apply the material beyond recommended pot life.Coverage: 206 - 350 sq ft/gal approximate Do not mix previously catalyzed material with new.NOTE: Brush or roll application may require multiple coats to In order to avoid blockage of spray equipment, clean equip-achieve maximum film thickness and uniformity of appearance. ment before use or before periods of extended downtime with Reducer #54, R7K54Drying Schedule @ 6.0 mils wet @ 50% RH: Material can not be sprayed if anti-slip aggregate is use. @ 50°F @ 77°F @ 120°F 30 minutes Anti-slip additives, such as H&C SharkGrip®, may be added toTo touch: 4 hours 2 hours the coating to provide some slip resistance. This product should 4 hours not be used in place of a non-skid finish.To recoat: 7 days 12 hours Prime coat for concrete may be reduced up to 1 pint per gallon.minimum: 24 hours 8 hours 24-36 hours 4 days Clear is for interior use only.maximum: 7 days 7 days 2 hours 10 minutes Refer to Product Information sheet for additional performanceFoot traffic: 48 hours 24 hours characteristics and properties.Heavy Traffic 4-5 days 48-72 hoursTo cure: 10 days 7 daysPot Life: 6 hours 4 hoursSweat-in-Time: 2 hours 30 minutesIf maximum recoat time is exceeded, abrade surface before recoat-ing.Drying time is temperature, humidity, and film thickness depen-dent.Application of coating above maximum or below minimum rec-ommended spreading rate may adversely affect coating per-formance.Anti-slip additive may be mixed into the final coat just prior toapplication. Exception: if anti-slip is desired with Clear finish, itshould be hand broadcast. CLEAN UP INSTRUCTIONS SAFETY PRECAUTIONSClean spills and spatters immediately with Reducer #54, Refer to the MSDS sheet before use.R7K54. Clean tools immediately after use with Reducer #54,R7K54. Follow manufacturer's safety recommendations when Published technical data and instructions are subject to changeusing any solvent. without notice. Contact your Sherwin-Williams representative for additional technical data and instructions.

THE Heavy 8.51SHERWIN-WILLIAMS ARMORSEAL® DutyCOMPANY REXTHANE™ I FLOOR COATING Floor B65-60 SERIES CoatingsINDUSTRIAL PRODUCT INFORMATION Revised 5/02 & MARINE COATINGS PRODUCT DESCRIPTION RECOMMENDED USESARMORSEAL REXTHANE I FLOOR COATING is a high sol- • For industrial, commercial, or marine applications where aids, single component, aliphatic, moisture cure urethane, VOCcomplying, moisture resistant industrial floor coating. This ure- heavy-duty polyurethane floor finish is requiredthane coating cures to a high gloss and chemical resistant filmequivalent to two-part urethane coatings. • Excellent resistance to alkalies, dilute acids, spillage of sol-• Impact and abrasion resistant vents, chemicals, jet fuel, grease, etc.• Chemical resistant• Resists yellowing • Formulated specifically for brush and roller application• Suitable for use in USDA inspected facilities• VOC compliant • Urethane floor coatings may exhibit tire tracking.• Fast 'hardness' development • Meets ADA requirements for slip resistance for floors PRODUCT CHARACTERISTICS • Interior or exterior use • Schools • Airport hangers • Laboratories • Pharmaceutical Houses • Clean rooms • Resists Skydrol • Graffiti resistant PERFORMANCE CHARACTERISTICSFinish: Gloss System Tested: (unless otherwise indicated)Color: Clear, White, Haze Gray, Deck Substrate: ConcreteVolume Solids: Gray, Sandstone, Tile Red (calculated) Surface Preparation: SSPC-SP13/NACE 6 67% ± 2%, WhiteWeight Solids: may vary by color 1 ct: ArmorSeal 1000 HS Clear @ 5.0 mils dft 81% ± 2%, may vary by color 1 ct: ArmorSeal Rexthane I @ 2.0 mils dft Abrasion Resistance: Method: ASTM D4060, CS17 wheel, 1000 cycles, 1 kg load Result: 116 mg lossVOC (EPA Method 24): Unreduced: 282 g/L; 2.41 lb/gal Adhesion: Reduced 10%: 335 g/L; 2.8 lb/gal Method: ASTM D4541 Result: 1466 psiRecommended Spreading Rate per coat: Hot Tire Pick-Up:Wet mils: 3.0 - 4.5 Method: ITM P213.00 @ 140°F Result: PassesDry mils: 2.0 - 3.0Coverage: 358 - 537 sq ft/gal approximateNOTE: Brush or roll application may require multiple coats to Moisture Condensation Resistance:achieve maximum film thickness and uniformity of appearance. Method: ASTM D4585, 100°F, 1000 hours Result: Rating 10 per ASTM D714 for blisteringDrying Schedule @ 3.0 mils wet @ 50% RH: Pencil Hardness: @ 40°F @ 77°F @ 100°F Method: ASTM D3363 Result: HTo touch: 4 hours 2 hours 30 minutes Slip Resistance, Floors:To recoat Method: ASTM C1028-96, .60 minimum Static Coefficientminimum: 48 hours 9 hours 3 hours of Friction Result: Passes wet and dry, with and without SharkGripmaximum: 14 days 14 days 14 days AdditiveFoot Traffic: 48 hours 24 hours 12 hoursHeavy Traffic: 7 days 3 days 3 daysTo cure: 7 days 3 days 3 daysDrying time is temperature, humidity and film thickness dependent.Shelf Life: 12 months, unopened, at 77°F Resists fumes, splash, and spillage of mild acids, alkalies, salts,Flash Point: 111°F PMCC aliphatic and aromatic hydrocarbon solvents, lubricating oils, and Skydrol. (ASTM D1308).Reducer/Clean Up: Aromatic 100, R2K5ArmorSeal 8.51 continued on back

I started the PC, but in BIOS it just shows me my two DVD-Rom drives.What am I doing wrong here?I was thinking of doing the CAP file by my own, i have seeen a turorial from fernando. But i cant find the 'uncompressed' File you mentioned above.Do i have to reset bios to default settings?Do i have to switch from RAID on SATA config to something else?What about CSM Module? Its active and for SATA UEFI drivers will be loaded.How can i make sure that my BIOS Flash was successful?thank you very much for your answersm0h. Asus rampage iv black edition x79 extreme. Hey, thanks for the quick reply.Switches are all on 'ON'.I did 'Load opimized default values' which is facory defaults i guess.-RAID switched to AHCI automaticallyFast Boot Disabled CHECKCSM Enabledall switched to UEFII cant change secure boot status and platform Key (PK) Status but it is the same as on your screenshot.Other OS is selected as well.I cant see the device on the BOOT Tab.

THE Heavy 8.51SHERWIN-WILLIAMS ARMORSEAL® DutyCOMPANY REXTHANE™ I FLOOR COATING Floor B65-60 SERIES CoatingsINDUSTRIAL PRODUCT INFORMATION & MARINE COATINGS RECOMMENDED SYSTEMS SURFACE PREPARATIONConcrete: Surface must be clean, dry, and in sound condition. Remove1 ct. ArmorSeal 1000 HS, reduced @ 1.5 - 2.0 mils dft all oil, dust, grease, dirt, loose rust, and other foreign material1-2 cts. ArmorSeal Rexthane I @ 2.0 - 3.0 mils dft/ct to ensure good adhesion.Concrete: Refer to product Application Bulletin for detailed surface prepa-1 ct. ArmorSeal FloorPlex 7100 Primer ration information. @ 1.5 - 2.0 mils dft Minimum recommended surface preparation:1-2 cts. ArmorSeal Rexthane I @ 2.0 - 3.0 mils dft/ct Concrete: SSPC-SP13/NACE 6Concrete - smooth:2 cts. ArmorSeal Rexthane I @ 2.0 - 3.0 mils dft/ct Wood: Clean, dry, sound, smoothSteel with Zinc Metalizing: Steel with Zinc1 ct. ArmorSeal Rexthane I Clear, mist coat, reduced Metalizing: Clean, dry, sound (clear coat only) 30% with R7K100. Allow to flash for 20 minutes.1 ct. ArmorSeal Rexthane I Clear @ 2.0 - 3.0 mils dft TINTING (Reduced 10% with R7K100) Do not tint.Wood:1-2 cts. ArmorSeal Rexthane I @ 2.0 - 3.0 mils dft/ct APPLICATION CONDITIONS Temperature: 20°F minimum, 100°F maximum air and surface 40°F minimum material: Do not apply over surface ice Relative humidity: Can be applied at relative humidi- ties up to 99%. Refer to product Application Bulletin for detailed application in- formation. ORDERING INFORMATION Packaging: 1 gallon containers All colors: 1 and 5 gallon containers Haze Gray: 12.09 ± 0.2 lb (may vary with color) Weight per gallon: SAFETY PRECAUTIONS Refer to the MSDS sheet before use.The systems listed above are representative of the product's Published technical data and instructions are subject to changeuse. Other systems may be appropriate. without notice. Contact your Sherwin-Williams representative for additional technical data and instructions.

THE Heavy 8.51ASHERWIN-WILLIAMS ARMORSEAL® DutyCOMPANY REXTHANE™ I FLOOR COATING Floor B65-60 SERIES CoatingsINDUSTRIAL APPLICATION BULLETIN Revised 5/02 & MARINE COATINGS SURFACE PREPARATION APPLICATION CONDITIONSGeneral Surface Preparation Temperature: 20°F minimum, 100°F maximumSurface must be clean, dry, and in sound condition. Remove air and surface 40°F minimumall oil, dust, grease, dirt, loose rust, and other foreign material material: Do not apply over surface iceto ensure good adhesion. Can be applied at relative humidi- Relative humidity: ties up to 99%.Concrete/MasonryNew APPLICATION EQUIPMENTSurface must be clean, dry, sound, and offer sufficient profileto achieve adequate adhesion. Minimum substrate cure is 28 The following is a guide. Any reduction must be compatibledays at 75°F. Remove all form release agents, curing com- with the existing environmental and application conditions.pounds, salts, efflorescence, laitance, and other foreign matterby sandblasting, shotblasting, mechanical scarification, or suit- Reducer/Clean Up ..... Aromatic 100, R2K5able chemical means. Refer to ASTM D4260. Rinse thoroughlyto achieve a final pH between 6.0 and 10.0. Allow to dry thor- Brushoughly prior to coating. Brush .............. Natural BristleOld Reduction ........... As needed, up to 10% by volumeSurface preparation is done in much the same manner as newconcrete; however, if the concrete is contaminated with oils, Rollergrease, chemicals, etc., they must be removed by cleaning with Cover .............. 3/8' woven with phenolic corea strong detergent. Refer to ASTM D4258. Form release Reduction ........... As needed, up to 10% by volumeagents, hardeners, etc. must be removed by sandblasting, shot-blasting, mechanical scarification, or suitable chemical means. If specific application equipment is listed above, equivalentIf surface deterioration presents an unacceptably rough sur- equipment may be substituted.face, ArmorSeal 5020 Floor Resurfacer is recommended topatch and resurface damaged concrete.Fill all cracks, voids and bugholes with ArmorSeal Crack Filler.Always follow the ASTM methods listed below:ASTM D4258 Standard Practice for Cleaning Concrete.ASTM D4259 Standard Practice for Abrading Concrete.ASTM D4260 Standard Practice for Etching Concrete.ASTM D4263 Plastic Sheet Method for Checking Moisture inConcrete.SSPC-SP13/NACE 6 Surface Preparation of ConcretePreviously Painted Surfaces:If in sound condition, clean the surface of all foreign material.Smooth, hard or glossy coatings and surfaces should be dulledby abrading the surface. Apply a test area, allowing paint to dryone week before testing adhesion. If adhesion is poor, or if thisproducts attacks the previous finish, removal of the previouscoating may be necessary. If paint is peeling or badly weath-ered, clean surface to sound substrate and treat as a new sur-face as above.Steel with Zinc Metalizing:Surface must be clean, dry and sound. Follow the recom-mended system from the Product Information Sheet.WoodSurface must be clean, dry and sound. Remove any oils anddirt from the surface using a degreasing solvent or strong de-tergent. Sand to remove any loose or deteriorated surface woodand to obtain a proper surface profile.ArmorSeal 8.51A continued on back

THE Heavy 8.51ASHERWIN-WILLIAMS ARMORSEAL® DutyCOMPANY REXTHANE™ I FLOOR COATING Floor B65-60 SERIES CoatingsINDUSTRIAL APPLICATION BULLETIN & MARINE COATINGS APPLICATION PROCEDURES PERFORMANCE TIPSSurface preparation must be completed as indicated. Spreading rates are calculated on volume solids and do not include an application loss factor due to surface profile, rough-Mixing Instructions: Mix paint thoroughly by boxing and stir- ness or porosity of the surface, skill and technique of the appli-ring before use. cator, method of application, various surface irregularities, material lost during mixing, spillage, overthinning, climatic con-Apply paint to the recommended film thickness and spreading ditions, and excessive film build.rate as indicated below: Excessive reduction of material can affect film build, appear-Recommended Spreading Rate per coat: ance, and adhesion.Wet mils: 3.0 - 4.5 Anti-slip additives, such as H&C SharkGrip®, may be added to the coating to provide some slip resistance. This product shouldDry mils: 2.0 - 3.0 not be used in place of a non-skid finish.Coverage: 358 - 537 sq ft/gal approximate Urethane floor coatings may exhibit tire tracking.NOTE: Brush or roll application may require multiple coats toachieve maximum film thickness and uniformity of appearance.Drying Schedule @ 3.0 mils wet @ 50% RH: Pour a small amount of Aromatic 100, R2K5 over the top of the paint in the can to prevent skinning or gelling. @ 40°F @ 77°F @ 100°F Place a temporary cover over the pail to keep excessive mois-To touch: 4 hours 2 hours 30 minutes ture, condensation, fog, or rain from contaminating the coat- ing.To recoat It is recommended that partially used cans not be sealed/closedminimum: 48 hours 9 hours 3 hours for use at a later date.maximum: 14 days 14 days 14 days Anti-slip additives, such as H&C SharkGrip®, may be added to the coating to provide some slip resistance. This product shouldFoot Traffic: 48 hours 24 hours 12 hours not be used in place of a non-skid finish.Heavy Traffic: 7 days 3 days 3 days Refer to Product Information sheet for additional performance characteristics and properties.To cure: 7 days 3 days 3 daysDrying time is temperature, humidity and film thickness dependent.Application of coating above maximum or below minimum rec-ommended spreading rate may adversely affect coating per-formance. CLEAN UP INSTRUCTIONS SAFETY PRECAUTIONSClean spills and spatters immediately with Aromatic 100, R2K5. Refer to the MSDS sheet before use.Clean tools immediately after use with Aromatic 100, R2K5.Follow manufacturer's safety recommendations when using any Published technical data and instructions are subject to changesolvent. without notice. Contact your Sherwin-Williams representative for additional technical data and instructions.